Paxton Net2 plus Instalační manuál stáhnout pdf

Page

1 redaeR

:noi

tuaC ylno sredaer CD V21 roF

2 red

aeR

12V

Red LED

Amber LED

Green LED

Data/D0

Clock/D1

Media Detect

12V

Red LED

Amber LED

Green LED

Data/D0

Clock/D1

Media Detect

N.C.

N.O.

COM

N.C.

N.O.

COM

Alarm

12V

Green LED

Exit

stupnI

tputsuO

rewoP

12V

Contact

Tamper

PSU

repmaT/USP

tcatnoC

nottuB tixE

2 yaleR

1 yaleR

Expansion

RS485 Network

CAT5 Cable Coding

nrG/thW

eraps ro neercS

atad morf seroc

lbac

nee

gnrO/thW

egn

arO

10/100 Ethernet

Server Connected

Server Link

100

End of Line Termination

OFF

Net2 plus

Intruder Alarm

Set

mrA

esneS

MOC

.O.N

LABEL HERE

http://paxton.info/107

123456

00-01-02-03-04-05

2345612

Exit button

(push to make)

Reader/keypad

Tamper switch

(optional)

Door contact switch

(held closed by door)

30/08/2012

12V DC

power supply

12V (Green) - Power LED.

Relay 1 (Orange) - The relay is energised - (N.O./COM contacts are closed).

Relay 2 (Orange) - The relay is energised - (N.O./COM contacts are closed).

Alarm (Red) - 12V Alarm output is active.

Exit (Orange) - The exit button contacts are closed.

Contact (Orange) - The door contacts are closed.

Tamper (Orange) - The tamper contacts are closed.

PSU (Orange) - The PSU contacts are closed.

OK (Green ash) - The internal software is running.

Termination (Red) - The on-board resistors are in place across the RS485 data pairs.

Rx (Red) - The ACU is receiving data (TCP/IP or RS485) - See also FAQ section.

Tx (Green) - The ACU is responding to data - (TCP/IP or RS485).

Server Connected (Green) - The TCP/IP interface is communicating with the PC Net2 server.

Server Link - Green = 100 Mbit/s : Orange = 10 Mbit/s (TCP/IP speed).

Switchable

120 ohm

resistors

The Net2 plus ACU has 2 reader ports and

3 output relays, but can control just one

door. The conguration of one control

unit per door greatly simplies installation

and is ultimately highly cost effective.

Intruder alarm integration

TCP/IP patch lead

To next

ACU

From previous

ACU

The Net2 plus can be connected to the PC via an RS485 data line or a TCP/IP connection.

This unit requires the controlling PC to be running Net2 v4.14 or later software.

For a fail open lock

(Maglock), wire 0V to the

"N.C." terminal instead of

"N.O."

Fail closed release

LED indications

Wiring

Ins-30080 Net2 plus control unit

Technical Support

Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT)

Saturday from 09:00 - 13:00 (GMT)

01273 811011

[email protected]

Documentation on all Paxton products can be found on our website - http://www.paxton.co.uk/

Paxton

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - 01273 811011

Page1 1 redaeR:noituaC ylno sredaer CD V21 roF 2 redaeR12VRed LEDAmber LEDGreen LEDData/D0Clock/D1Media Detect0V0V12VRed LEDAmber LEDGreen LEDData/D0

Strany 2 - Site Layout Examples

Page2A Net2 plus can connect to the Net2 PC using either an un-shielded RJ45 patch cable or an RS485 data line. This greatly increases the number of i

Strany 3 - 30718 UDP

Page3Connecting to the PC via the Ethernet port The IP address should be assigned a xed value, or should be given a DHCP reservation. Unreserved IP

Strany 4 - TCP/IP Loopback test

Page490% of installation faults are caused by wiring errors on the RS485 data line. Special attention to getting this right rst time saves a lot of t

Strany 5 - Software Conguration

Page5Intruder alarm integration A dedicated port for input and output signals is provided when integrating a Net2 plus ACU with an alarm system.Please

Strany 6 - Technical Help

Page61 - RS485 Data line resistance check - ACU not responding or fails to be detected.QFirst power down any data line converters and disconnect any

Strany 7

Page77 - Fire alarm integration - Net2 Professional software must be used.QA voltage free normally closed contact from the re alarm system should be

Strany 8 - Specications

Page850,000 Net2 v4.1650,000 Net2 v4.1625064501222200200 Net2 v4.212,72810 Mbit/s 100 Mbit/s200 kbit/s115.2 kbit/s11V DC 15V DC200 mA24V DC4 A1 A500 m

Komentáře k této Příručce

Žádné komentáře

Paxton Net2 plus Instalační manuál

Procházejte online nebo si stáhněte Instalační manuál pro Bezpečnostní dveřní ovladače Paxton Net2 plus. Paxton Net2 plus Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní dveřní ovladače Paxton Net2 plus